Speedhut 3-3_8 inch, 4 inch, & 4-1_2 inch Quad_Dual Gau Bedienungsanleitung PDF herunterladen

Ground (black)

+12 volts Dash lighting (white)

Snap connection

for dial lighting

Inverter

Setting warning LED for both low and high.

Led can be set to turn on for both a low or high condition for temperature, pressure gauges, and voltage gauges. Fuel level warning light is ONLY for the low fuel

condition.

To reset LED set point at any time follow this procedure again.

1. To enter LED calibration mode, Press and hold button with gauge power off. Turn on gauge power. Release button. You will see each warning LED light up

for 2 seconds. Pressing and releasing the button while that particular gauges warning light is lit will enter the set point for that gauge.

2. Pointer will slowly scan clockwise from full low condition on dial. Press button at desired low warning set point. LED will blink to indicate low warning has been

set. Note: Pressing button at full low on dial will turn off Lean LED warning so that it does not light up.

3 Pointer will now travel to full high condition on dial and slowly scan counterclockwise. Press button at desired set point for high condition. LED will blink to

indicate high warning has been set. Note: Pressing button at max high position on dial will turn off high LED warning so that it does not light up.

Note: Setting a low warning will turn on LED when pointer travels below the low set point. Setting a high warning will turn on LED above the high set point.

4. Repeat procedure for next gauge.

5. Turn gauge power off and back on to exit menu.

(Black)

Pressure

(Black)

Temperature

1.Disconnect negative (-) Battery Cable

2. Connect wiring as above.

3. Mount Gauge for easy viewing. Use spin lock ring (included) to mount to panel. Spin ring

threads in both directions (depending on your dash panel thickness). Snap gauge connector to wiring connector

4. Reconnect negative (-) battery cable.

1/8 npt threads

+12 volts keyed ignition

(Red)

(Black)

Ground

(White)

+12 volts Dash lighting

Power distribution cable to plug all gauges into

(Black)

White wire Fuel level

signal wire.

Set the warning light option.

Note: Tie both lighting white wires together

and both black ground wires together.

INVERTER IS REQUIRED FOR GAUGE DIAL LIGHTING

(Gauge Dial lighting)

(Main gauge power)

(Pointer (needle) lighting)

Fuel sender ground

should be connected

to the fuel level sender

ground. If you do not

have a fuel level sender

ground connect to the

chassis ground.

Inverter Note: E18-686-5CR is single gauge inverter to light single gauge.

C01-18N-2 & C11-18A01 are multiple gauge lighting inverters that can light

up to 6 - 8 gauges depending on inverter model.

will remain in last powered position.

Power Draw = 0.2 Amp

5 Amp Inline Fuse Recommended

for +12 Keyed Ignition

1/8 npt threads

Trimable area

DO NOT trim pass the slot.

4-1/2”, 4”, and 3-3/8” Quad / Dual Gauge Instructions

1 2

Inverter 1
CHART 1: 2

Inhaltsverzeichnis

Seite 1 - Inverter

Ground (black)+12 volts Dash lighting (white)Snap connectionfor dial lightingInverter Setting warning LED for both low and high. Led can be set to tur

Seite 2 - CHART 1:

Peak recall memoryPress and hold gauge button down and gauge needle pointers will move between low and high peak on all gauges (except fuel level).

Kommentare zu diesen Handbüchern

Keine Kommentare

Speedhut 3-3_8 inch, 4 inch, & 4-1_2 inch Quad_Dual Gau Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Speedhut 3-3_8 inch, 4 inch, & 4-1_2 inch Quad_Dual Gau herunter. Speedhut 3-3_8 inch, 4 inch, & 4-1_2 inch Quad_Dual Gauge User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern